Abstract. This paper describes a computer-aided design for design of the concave globoidal cam with cylindrical rollers and indexing turret. Abstract—This paper describes a computer-aided design for design of the concave globoidal cam with cylindrical rollers and swinging follower. Four models. Globoidal Cams combine great strength and stiffness with compactness. MechDesigner will calculate the Globoidal cam profile to machine accuracy (no.
|Published (Last):||14 May 2011|
|PDF File Size:||6.15 Mb|
|ePub File Size:||14.99 Mb|
|Price:||Free* [*Free Regsitration Required]|
Embed this code snippet in the HTML of your website to show this chapter.
In this study, the four models above were created on a notebook with 1. In this study, the concave globoidal cam with swinging roller follower is modeled from angular input and output displacements.
These indexers convert a uniform input motion gloobidal an intermittent Your suggestions for improvement: Creating the assembly model. After that, use the Mechanism Design module to define the geometrical relationships of the system, make it move and analyze its motion also. Conclusion In this study, four modelling methods are developed to create the concave globoidal cam.
Thank-you for your help. Obviously, these gaps also cause errors in the output angular displacements but g,oboidal errors are very small and can be accepted.
Design and Manufacture Globoidal Cams
These angular displacements can be extracted from the NC program generated by some special sofwares that are specialized for cam mechanisms. Our readership spans scientists, professors, researchers, librarians, and students, as well as business professionals. With DirectIndustry you can: Globoidal Cam Indexers Right angle indexers are typically used for continuously running applications with cams designed to match the indexing and idle The angle between two axes of glooboidal rollers is 60 0.
There are 10 positions of interference in the assembly of former, while there are a lot ccam positions of interferences for the latter. Subscribe to our newsletter. If they are large, the errors of output angular displacements will be large and the model in this case may have to be eliminated.
The following is the procedure to make animation and check interference. The servo motor is always applied on the cam axis so that the cam can move about its axis.
Create the origin trajectory and two 3D curves Figure 1 1b. Figure 2 shows two subtypes of the concave globoidal cam: In this study, the single thread-type is the globoidal cam that we will deal with. It globoifal only few minutes to create the pitch surface, floboidal most time-consuming task, for the model of the first method graphs-based method.
Design and Manufacture Globoidal Cams – any Motion
Cut a bank by sweeping a rectangular section Figure 7 to form the cam surfaces if the following constrains are performed: The working surfaces of the globoidal cams are the surfaces that contact with the roller surfaces. It is the height of the point P and presented as.
Create a revolution surface of the globoidal body of the cam Figure 1 1a. These errors may be so very high that the model cannot be acceptable. Servo motor can also be applied for the follower. This is because when creating the pitch surfaces in the methods which need 3D curves, the system has to interpolate the glohoidal surface through physical points on this curve.
The followings are three methods that can be used to create the pitch surface. The width of the section is equal to the diameter of the roller. They are constructed in a small enclosure made from iron alloy and are integrated with wide mounting positions.
Globoidal cam indexer – All industrial manufacturers – Videos
When the globoidal cam rotates, the follower will stay or rotate depending on the location of the rollers on the cam surfaces. By Algebra Veronica Vargas A. A cam set converts a uniform input There are some calculations that must be done before making the models as follows: The working surfaces of the cam can be obtained from the pitch surfaces by offsetting them a distance that is equal to the radius of the roller.
Although the interference does not occur between the cam surfaces of the acceptable models with their rollers, but there may have clearances between them. Section 2 presents the theoretical background of concave globoidal cam. From these coordinates and some other information, the pitch surfaces of the cam can be modeled. These cams are used for small angles of follower oscillation. Create the two pitch surfaces by using the Variable Section Sweep command Figure 1 1c.
Finally, conclusion globboidal are given in Section 5. The graphs-based method Create a revolution surface of the globoidal body of the cam Figure 9 a. If the start point caj encountered after the datum plane then 0 is positive. To see the cam easily, the pitch surfaces on four final models in figures 9 to 12 are hidden.
Evaluate the quality of the search results: The origin trajectory in this case is the circle which is the intersection between datum plane and the cam body.
In order to make animation and verify the interference between components in the globoidal cam mechanism, first, an assembly of the cam and globoieal follower is made.